Setting Up
[C203/C204] How do I pair my zigbee lighting module to my zigbee hub?
For pairing instructions specific to Home Assistant, Hubitat, Philips Hue or Smartthings please click the relevant link below: Home Assistant pairing instructions Hubitat pairing instructions Philips Hue pairing instructions Smartthings pairing ...
[C201] How do I pair my zigbee lighting module to my zigbee hub?
For pairing instructions specific to Home Assistant, Hubitat, Philips Hue or Smartthings please click the relevant link below: Home Assistant pairing instructions Hubitat pairing instructions Philips Hue pairing instructions Smartthings pairing ...
[C203/C204] How I do pair my dimming module to Philips Hue?
Firstly, we recommend doing a factory reset: Turn on the light, press and hold the reset button for over 5 seconds. Then put the switch in network pairing mode. Double press the reset button to activate zigbee pairing mode. In your Philips Hue app, ...
[C201] How do I pair my zigbee lighting module to Philips Hue?
Firstly, we recommend doing a factory reset: Turn on the light, press and hold the reset button for over 5 seconds. Then put the switch in network pairing mode. Double press the reset button to activate zigbee pairing mode. In your Philips Hue app, ...
[C203/C204] How do I pair my zigbee lighting module to Hubitat Elevation?
Factory reset the module: After powering on the module for the first time, the lamp should slowly blink. If it does not blink, you will need to factory reset the device. To do this, press the reset button 5 times. If the module is not accessible, ...
[C203/C204] Advanced configuration
Set up a Touchlink remote Press the reset button 4 times or turn the power off/on 4 times. Bring the remote within 10cm of the module and set the remote into Touchlink commissioning mode. You will need to refer to the instructions that came with the ...
[C203/C204] Setting minimum brightness
Adjust the brightness to the desired minimum level using your smart controller app This is typically the lowest level possible where a dim glow is visible without any flickering. Press and hold the Min Set button on the module for 3 seconds (C204) or ...
[C203/C204] How do I pair my zigbee lighting module to Home Assistant?
Factory Reset the module: After powering on the module for the first time, the lamp should slowly blink. If it does not blink, you will need to factory reset the device. To do this, press the reset button 5 times. If the module is not accessible, ...
[C201] How do I pair my zigbee lighting module to Home Assistant?
Factory Reset the module: Press and hold the reset button for 5 seconds. The LED will go red for 10 seconds, after which the reset is complete. Add the module to your Home Assistant: Open your Home Assistant dashboard. Go to the menu and click on ...
[C201] How do I pair my zigbee lighting module to Hubitat Elevation?
Please note the new driver is currently for product codes #10 and above. Do not install it if your product code # is below 10. You can identify the # code on the back of the device. If you have multiple devices, of both compatible and incompatible ...
[C203/C204] How do I pair my zigbee lighting module to Samsung Smartthings?
Factory Reset the module: After powering on the module for the first time, the lamp should slowly blink. If it does not blink, you will need to factory reset the device. To do this, press the reset button 5 times. If the module is not accessible, ...
[C203/C204] Wiring Instructions
Turn off the power To avoid electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation and maintenance. Be aware that even if the circuit breaker is off, some voltage may remain in ...
[C201] Adjusting dimming settings
To optimise the performance of the smart module, or to adjust the settings to your preference, you can adjust the brightness at the Min. and Max. level, and adjust dimming speed. MIN adjustment - Switch on the lights. When the lights are on, insert a ...
[C201] Advanced configuration
TouchLink to a Zigbee Remote Press the reset button 4 times. The LED will start blinking green indicating that the module is ready for Touchlink mode. Pairing mode will time-out after 15 minutes. Bring the remote within 10cm of the module and set the ...
[C201] How do I pair my zigbee lighting module to Samsung Smartthings?
Please note the new driver is currently for product codes #10 and above. Do not install it if your product code # is below 10. You can identify the # code on the back of the device. If you have multiple devices, of both compatible and incompatible ...
[C201] Wiring Instructions
Turn off the power. To avoid electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation and maintenance. Be aware that even if the circuit breaker is off, some voltage may remain in ...